PH Customz

Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: Rubicon wont move!!


Member

Status: Offline
Posts: 24
Date:
Rubicon wont move!!


So i have an 05 rubicon an it wont move! It drove fine all nite then stoped to drink a lil. Started it bak an now it wont go. You jack up the rear an it will slowly get the tires going. But with it on the ground it jus wont go! I need help!

__________________

Honda 450 foreman 10 inch sra lift 14.5 gr jetted dg clutch discs am springs epi clutch kit fo/04 32 terms



Veteran Member

Status: Offline
Posts: 29
Date:

dont run it no more. you my not have any oil presser. thats what runs the trans on them bikes. i have heard of a few of them doing this.

__________________

300 on 32s aka(brute getter)

300 with 5inch lift 30s

420 (beer bike)



.

Status: Offline
Posts: 440
Date:

do they have centrifugal clutches?
that blue rancher i had, the original 400 engine did, and the dogs went out..which is why it got the stroked 450 engine..

__________________
To each thier own....


Veteran Member

Status: Offline
Posts: 67
Date:

Pull the oil filter cover & filter, then fire it back for a second with a drain pan under it and see if you have oil flow. - As outlaw noted, the oil pump in those is chain driven and feeds the transmission as well as the motor. They have been known to break the chain with age/wear.



-- Edited by JPs300 on Friday 22nd of July 2011 02:30:57 PM

__________________

'09 Thundercat - 1000ish

SpeedWerx powa, /// WCD, 4" catvos, 29.5 terms

'96 300
...a little taller & a little more power than most.....



Veteran Member

Status: Offline
Posts: 29
Date:

jgmood050 wrote:

do they have centrifugal clutches?
that blue rancher i had, the original 400 engine did, and the dogs went out..which is why it got the stroked 450 engine..


 im not sure if they are like that or not. i have seen the 400 do that a time or 2. the cluthces get wore and losse oil presser so they wont move and if they do its like there under a load. it toke a while to figure that one out. lol



__________________

300 on 32s aka(brute getter)

300 with 5inch lift 30s

420 (beer bike)



Member

Status: Offline
Posts: 24
Date:

Ok so ima check the oil pressure this week! But sum people have ben sayn its the anhle position sensor. Sum people say its my tires too! I have 32 terms with no gr or clutch kit! Jus an exhaust but it pulls them fine in 2 wheel so i dont kno! I hate electronics!!

__________________

Honda 450 foreman 10 inch sra lift 14.5 gr jetted dg clutch discs am springs epi clutch kit fo/04 32 terms



Veteran Member

Status: Offline
Posts: 67
Date:

IDK the rubicon or ES type bikes that well, but I don't think a bad angle sensor will stop the bike from moving, only stop it from shifting correctly.

__________________

'09 Thundercat - 1000ish

SpeedWerx powa, /// WCD, 4" catvos, 29.5 terms

'96 300
...a little taller & a little more power than most.....



Member

Status: Offline
Posts: 24
Date:

Well i finally got around to checking the iil pressure. No oil came outta the oil filter so i have startd tearung it down but cant seem to find the oil pump chain so ima have to buy a book. Thanks for the help!! Itll have a good list of goodies after this tho!!

__________________

Honda 450 foreman 10 inch sra lift 14.5 gr jetted dg clutch discs am springs epi clutch kit fo/04 32 terms

Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.



Create your own FREE Forum
Report Abuse
Powered by ActiveBoard